Field report SE-64 / P5 · sheet /operations
Operations & RestructuringFiled from the territory
Why Grid Operators Cut Power on Purpose: Inside Rolling Blackouts
Grid operators cut power on purpose to prevent collapse: staged relays trip below 60 hertz, NERC alerts escalate, and California 2020, Texas 2021 and Eskom show three very different outcomes.
- Grid
- SE-64 / P5
- Surveyed
- November 20, 2026
- Reading
- 3 min read
- Correspondent
- Elena Vasquez

Field notes
- CAISO ordered rotating outages on Aug. 14–15, 2020, the first since the 2000–2001 energy crisis
- ERCOT's February 2021 load cuts broke rotation, leaving many Texans dark far longer than planned
- Eskom has run scheduled load shedding since 2007–2008
- Under-frequency relays trip automatically below 60 hertz in North America without dispatcher approval
- NERC's Energy Emergency Alert level three means firm load cuts are imminent or under way
By Elena Vasquez
Electric utilities sometimes switch off their own customers deliberately to keep a far larger share of them connected. That trade sits at the center of rolling blackouts, one of the last tools grid operators deploy during a supply emergency — and the mechanics, laid out in a new ten-part explainer, trace the method from frequency mathematics to the staged process of restoring power.
The logic starts with a hard constraint. Electricity cannot be stored cheaply at grid scale. Power plants must produce exactly what homes, offices and factories draw at every moment, because oil sits in tanks and gas waits in underground storage, but grid power is consumed almost the instant it is generated.
What happens when the grid runs short?
A shortage shows up first as a drop in grid frequency — the rhythm of alternating current, targeted at 60 hertz in North America and 50 hertz in Europe. Generators spin in step with that rhythm. When demand exceeds supply, turbines slow and frequency falls with them.
Larger drops carry real danger. Power plants run protective systems that disconnect them if frequency strays too far from normal, because running off design speed damages costly equipment. Every trip pulls supply from an already short grid, pushing other plants past their limits. That chain reaction is how a manageable shortage becomes a system-wide collapse. Grids with more inverter-connected solar and batteries, and less rotating mass, see frequency move faster after a sudden loss.
How do controlled cuts actually work?
A rolling blackout interrupts that chain deliberately. Operators cut a defined amount of demand, then rotate the cuts among groups of customers so no single neighborhood absorbs the whole shortfall. One group's power returns only as another group's goes out; the total reduction holds steady through each cycle.
Two systems execute the cuts. Under-frequency relays act automatically: each relay watches frequency, and when it sinks to a preset threshold below 60 hertz, the relay opens a breaker with no dispatcher's approval. The settings come in staged steps that shed only as much demand as the emergency requires. The North American Electric Reliability Corp. sets the standards governing how these schemes are coordinated across regions.
Manual shedding works in minutes rather than fractions of a second, following NERC's Energy Emergency Alert levels one through three. Level three means firm load interruption is imminent or under way. The California Independent System Operator calls its equivalent tier a Stage 3 emergency.
Utilities select which neighborhoods go dark by distribution circuit, not by home or street. Circuits serving hospitals and emergency services are typically exempted where possible — which also spares every other customer on that same line, while shrinking the pool of circuits left to share the burden.
How do the famous cases compare?
- California, Aug. 14–15, 2020: CAISO ordered rotating outages during a heat wave, the first such orders since the 2000–2001 energy crisis. Cuts rotated as designed.
- Texas, February 2021: ERCOT ordered load cuts during a severe winter storm. The rotation broke down — the shortage ran too deep to restore one group before cutting the next, leaving many Texans dark far longer than a planned rotation.
- South Africa: State-owned Eskom has run scheduled cuts it calls load shedding since 2007–2008 — a repeated practice, not a single emergency.
Triggers overlap: heat waves drive simultaneous air-conditioning demand and cut how much current lines can carry; cold snaps raise heating load while freezing plant water lines, sensors and valves; fuel shortfalls, transmission limits and drought add further strain.
What comes before the cuts, and after?
Operators try imports, demand response — paying large customers such as factories to reduce use — and voluntary public appeals like California's Flex Alert before ordering outages.
Restoration is not a single switch. The hazard is cold-load pickup: refrigerators, air conditioners, water heaters and furnaces that cycled on and off before the outage all start at once when power returns, drawing a surge that can trip circuits. Operators reconnect load in measured blocks to spread that surge over time.
Short, shared outages, the explainer concludes, are the price a grid pays to avoid an uncontrolled blackout.
via qz.com (Source)
More from Elena Vasquez
Show full bio
Staff writer covering companies, deals and strategy in corporate strategy and chief-executive leadership at CEO Frontier.
514 articles